Meet us at these events
Meet us at Industry Space Days 2026
Meet us at BSBF 2026
Exhibiting with Asensor Technology
Expertise

Technical expertise and knowledge

Six technical domains:

System-level engineering

Complex systems often include multiple domains

The decisive design choice, or the real cause of a failure, usually lives in the interaction between electronics, firmware, power, EMC, components and physical construction, not inside one of them. That is the level the work starts at, and the level it can descend from, down to schematic, PCB, component and firmware.

Precision analogue & sensing

From sensing element to calibrated measurement system: circuitry, conversion, calibration, and everything physical around it.

Low-noise analogue24-bit acquisitionSensor interfacesError budgetsCalibrationMixed-signal layout
Technical details

Analogue & mixed-signal

  • Low-noise, low-offset front ends; precision differential amplification
  • Up to 16 analogue channels; 24-bit high-dynamic-range measurement
  • ADCs, DACs, precision references; anti-alias filtering
  • Offset, gain, linearity and temperature-drift; noise & error budgets
  • Stability with capacitive sensors and long cable loads

Sensor technologies

  • Hall & magnetic sensing; fields above 5 T; contactless current
  • Position/displacement; Pt100/Pt1000/Ni1000; ultrasonic; acceleration

Packaging & production

  • Bare die, wafer-test concepts, lead-frame & package design
  • QFN, BGA, ceramic; chip-on-board; assemblies below 300 µm
  • Calibration, trim-and-form, end-of-line test, production variation

Embedded & real-time control

Hardware and firmware as one system, where timing controls a machine.

Real-time firmwareMulti-axis servoPTP timingEtherCAT / CANGigabit EthernetFPGA
Technical details

Real-time & timing

  • Bare-metal, deterministic execution; latency & jitter budgets
  • Precision Time Protocol (PTP) and synchronised machine timing
  • Interrupts, state machines, scheduling, fault handling

Motion & servo

  • Real-time servo loops, multi-axis coordination, servo profiles
  • Dual-lane operation extended from a single-lane architecture

Communication & devices

  • EtherCAT, CAN, Gigabit Ethernet and high-speed interfaces
  • Microcontrollers and programmable logic (FPGA)
  • Power-up, reset and safe-state architecture

Power, drives & motion

Building systems that still work perfectly while switching, braking, charging and under fault.

H-bridgesMotor & servo driveLi-ion chargingSurge / EFT / ESDLoad dumpDerating
Technical details

Conversion & drive

  • Supply architectures, regulators, power stages
  • H-bridges, motor outputs, switching & dead-time
  • Inductive/capacitive loads; regenerative energy

Battery & charging

  • Li-ion charging; impedance, ageing, power-quality analysis
  • Charger hardware validation

Protection & lifetime

  • Inrush, surge, EFT, ESD, overvoltage; reverse polarity & load dump
  • Current limiting, controlled shutdown/start-up/recovery
  • Thermal behaviour; derating across V, I, P and temperature

EMC & signal integrity

Designing correctly from the start, as a way of working, not just implementing a test to pass.

Return pathsGrounding & bondingShieldingPCB stack-upLightning (DO-160)Pre-compliance
Technical details

Architecture & coupling

  • Common- and differential-mode; controlled return paths & loop areas
  • Grounding, bonding, shielding; shield termination
  • Parasitic capacitance/inductance; cable & connector coupling

Integrity & robustness

  • PCB stack-up & layout; signal and power integrity
  • ESD, RF, EFT, surge; lightning protection to DO-160

Investigation

  • Internal high-frequency currents not seen in standard tests
  • EMC-induced functional failures; pre-compliance measurement
  • Passing a test vs functioning reliably

Components & lifecycle

Choosing components for the best quality and lifecycle. Reviewing designs to predict and solve obsoleteness issues.

Worst-case & tolerancesSafe operating areaDeratingUL94Second-sourceObsolescence
Technical details

Selection on real behaviour

  • Beyond the datasheet headline: tolerances, worst-case, parasitics
  • Safe operating area; derating across V, I, P and temperature

Reliability & construction

  • Ageing, reliability, mission profiles; package & mounting
  • PCB materials; thermal/mechanical loading; UL94 flammability

Supply & obsolescence

  • Supplier, alternative and second-source qualification
  • Obsolescence transitions; compliance & production kept intact

Validation & root-cause

The investigation of design and system behaviour: finding the mechanism that created the failure, not just its symptom.

Hypothesis-drivenSPICE & worst-caseIntermittent faultsSymptom vs causeDFM / DFT
Technical details

Measurement & simulation

  • Establishing the truly decisive measurement; setup-influence checks
  • Circuit simulation (SPICE) for worst-case and margins before hardware
  • Correlating measurements with physical models

Failure investigation

  • Reproducing intermittent and conditional failures
  • Symptom vs cause across system, schematic, layout, firmware
  • Variation between units, batches, production conditions

Verification

  • Worst-case/boundary testing; verification & qualification; DFM/DFT
  • Proving the correction removes the real cause
Applied engineering judgement

Knowledge and experience across all fields

Need an expert who has experience in all these disciplines?

See the portfolioor call +31 6 5159 0081